|
Der Renesas Compact Emulator (CPE) bietet alle, für eine moderne Entwicklung
benötigten Funktionen, wie zum Beispiel Real-Time Trace und Hardware
Breakpoints, ist aber trotzdem zu einem erschwinglichen Preis erhältlich.
Verglichen mit einem konventionellen In-Circuit Emulator, hat der Compact
Emulator eine wesentlich kompaktere Bauform. Das Produkt-Paket enthält nicht nur
den Emulator und alle benötigten Verbindungskabel, sondern auch alle benötigten
Software-Werkzeuge, so dass sofort mit der Arbeit begonnen werden kann.
Der Compact Emulator wird über ein Konverter Board an das Zielsystem
angeschlossen. Mikrocontroller-spezifische Pakete bestehend aus Emulator und
Konverter Board werden als Set angeboten.
Eigenschaften
- Basis Debug Funktionen
- Real-Time Trace Funktionen
- Kompaktes Gehäuse
- Inklusive Programmier- und Debug-Software
- Erschwinglicher Preis
- Anschluss an PC über USB (USB1.1, Full-Speed)
Spezifikationen CPE für M16C/Tiny
|
MCU supported
|
M16C/Tiny Series M16C/26A, M16C/28, M16C/29 Group
|
|
Maximum operating clock frequency
|
20MHz (at 3.0 to 5.0V)
10MHz (at 2.7 to 3.0V)
|
|
MCU mode supported
|
Single-chip mode
|
|
Target system voltage
|
2.7 to 5.5V
|
|
Basic debugging function
|
Download, S/W break (64 points), Program execution/stop (allows free-run
execution and execution supporting S/W breaks) , Memory reference/setting
(reference/setting C-variables, run-time execution) , Register
reference/setting, Disassemble display, C-level debugging, etc.
|
|
Real-time tracing
|
Trace range
|
64K cycles
|
|
Trace data
|
20-bit address, 16-bit data, 12-bit MCU status
|
|
Trace modes
|
5 modes (Break/Before/About/After/Full)
|
|
Real-time RAM monitor
|
Range
|
1024 bytes (256 bytes x 4 blocks)
|
|
Results
|
Data, Latest access attribute (Read/Write/Non-accessed)
|
|
Hardware break function
|
2 points (Address break, R/W break, 255 pass counts) *1
|
|
Execution time measurement
|
Time between program start to stop is measurable.
|
|
PC Interface
|
USB (USB 1.1, Full-speed)
* Connectable to PC with a USB 2.0 port.
|
|
Power source for the emulator
(Available separately)
|
5.0V±5% DC/2A supplied from external source. (A power source unit is not
included.)
|
|
Power voltage
and power supply
|
With a target
|
2.7 to 5.0V (Supplied from Vcc terminal on the target.)
|
|
Without a target
|
3.3V/5.0V switchable (Supplied from the emulator body)
|
|
Operating environmental conditions
|
[Temperature] 5 to 35ºC, [Humidity] 20 to 80%, [Dust and dirt] General office
environment
|
|
Storage environmental conditions
|
[Temperature] -10 to 60ºC, [Humidity] 0 to 90%, [Dust and dirt] General
office environment
|
|
Overseas standards
|
EN55022: 1998 Class A, EN55024: 1998
|
*1.The hardware break function and trace point setting of the real-time trace
function cannot be used simultaneously.
Spezifikationen CPE für M16C/Tiny
|
MCU supported
|
M16C/60 Series M16C/62P Group
M16C/30 Series M16C/30P Group
|
|
MCU mode supported
|
Single-chip mode,
Memory-expansion mode (NORMAL, 4MB),
Microprocessor mode (NORMAL, 4MB) * For microprocessor mode, the emulation
memory board R0E33062PMSRC0 (option) is required.
|
|
Maximum ROM/RAM capacity
|
1. Internal flash ROM : 512KB + 4KB
0F000h--0FFFFh, 80000h--FFFFFh
2. Internal RAM : 31KB
00400h--07FFFh
|
|
Maximum operating clock frequency
|
24MHz (at 3.0 to 5.5V)(when using a PLL)
10MHz (at 2.7V)
|
|
Emulation memory
*For microprocessor mode, the emulation memory board R0E33062PMSRC0 (option) is
required.
|
External area (CS3*--CS0* area)
In the MAP tab in the MCU setting dialog box of the emulator debugger, memory
area assigned to the emulation memory can be allocated up to 4 areas by 4KB.
- Maximum operating frequency (at 5.0 V) 0-wait: 7 MHz
1-wait: 20
MHz
2-wait,
3-wait: 24MHz
- Maximum operating frequency (at 3.0 V) 0-wait: 6 MHz
1-wait: 17
MHz
2-wait,
3-wait: 24MHz
|
|
Target system voltage
|
2.7 to 5.5V
|
|
Basic debugging function
|
Download, S/W break (64 points), Program execution/stop (allows free-run
execution and execution supporting S/W breaks) , Memory reference/setting
(reference/setting C-variables, run-time execution) , Register
reference/setting, Disassemble display, C-level debugging, etc.
|
|
Real-time tracing
|
Trace range
|
64K cycles
|
|
Trace data
|
20-bit address, 16-bit data, 12-bit MCU status
|
|
Trace modes
|
5 modes (Break/Before/About/After/Full)
|
|
Real-time RAM monitor
|
Range
|
1024 bytes (256 bytes x 4 blocks)
|
|
Results
|
Data, Latest access attribute (Read/Write/Non-accessed)
|
|
Hardware break function
|
2 points (Address break, R/W break, 255 pass counts) *1
|
|
Execution time measurement
|
Time between program start to stop is measurable.
|
|
PC Interface
|
USB (USB 1.1, Full-speed)
* Connectable to PC with a USB 2.0 port.
|
|
Power source for the emulator
(Available separately)
|
5.0V±5% DC/2A supplied from external source. (A power source unit is not
included.)
|
|
Applicable power supply
|
User system connected
|
Vcc1 = Vcc2: 2.7--5.5V
Vcc1 > Vcc2: 4.8V ≤ Vcc1 ≤ 5.2V,
2.7V ≤ Vcc2 < Vcc1
|
|
User system not connected
|
3.3 V or 5.0 V
(supplied from the emulator)
|
|
Operating environmental conditions
|
[Temperature] 5 to 35ºC, [Humidity] 20 to 80%, [Dust and dirt] General office
environment
|
|
Storage environmental conditions
|
[Temperature] -10 to 60ºC, [Humidity] 0 to 90%, [Dust and dirt] General
office environment
|
|
Overseas standards
|
EN55022: 1998 Class A, EN55024: 1998
|
*1.The hardware break function and trace point setting of the real-time trace
function cannot be used simultaneously.
Spezifikationen CPE für M32C
|
MCU supported (*1)
|
M32C/80 Series M32C/84 (*2), M32C/85, M32C/86 Group
M32C/80 Series M32C/87 Group (separate CPE!)
|
|
Maximum operating clock frequency (*5)
|
Vcc1=Vcc2=4.2 to 5.5V : 32MHz
Vcc1=Vcc2=3.0 to 5.5V : 24MHz
Dual-power supply specification (4.8V ≤ Vcc1 ≤ 5.2V and 3.3V ≤ Vcc2 < Vcc1) :
32MHz
|
|
MCU mode supported
|
Single-chip mode
Memory expansion mode (*3)
|
|
Target system voltage
|
3.0 to 5.5V
|
|
Basic debugging function
|
Download, S/W break (64 points), Program execution/stop (allows free-run
execution and execution supporting S/W breaks) , Memory reference/setting
(reference/setting C-variables, run-time execution) , Register
reference/setting, Disassemble display, C-level debugging, etc.
|
|
Real-time tracing
|
Trace range
|
64K cycles
|
|
Trace data
|
20-bit address, 16-bit data, 12-bit MCU status
|
|
Trace modes
|
5 modes (Break/Before/About/After/Full)
|
|
Real-time RAM monitor
|
Range
|
1024 bytes (256 bytes x 4 blocks)
|
|
Results
|
Data, Latest access attribute (Read/Write/Non-accessed)
|
|
Hardware break function
|
2 points (Address break, R/W break, 255 pass counts) ( *4)
|
|
Execution time measurement
|
Time between program start to stop is measurable.
|
|
PC Interface
|
USB (USB 1.1, Full-speed)
* Connectable to PC with a USB 2.0 port.
|
|
Power source for the emulator
(Available separately)
|
5.0V±5% DC/2A supplied from external source. (A power source unit is not
included.)
|
|
Power voltage
and power supply
|
With a target
|
3.0 to 5.5V (Supplied from Vcc terminal on the target.)
|
|
Without a target
|
3.3V/5.0V switchable (Supplied from the emulator body)
|
|
Operating environmental conditions
|
[Temperature] 5 to 35ºC, [Humidity] 20 to 80%, [Dust and dirt] General office
environment
|
|
Storage environmental conditions
|
[Temperature] -10 to 60ºC, [Humidity] 0 to 90%, [Dust and dirt] General
office environment
|
|
Overseas standards
|
EN55022: 1998 Class A, EN55024: 1998
|
*1. For debugging 144-pin MCU, M3T-FLX-144NSD (option) is required.
*2. When using this emulation probe, you cannot use the page mode control
function for a ROM-less version of M32C/84 Group.
*3. An expansion memory space is only used as user space. An emulation memory
for an expansion memory space is not installed.
*4.The hardware break function and trace point setting of the real-time trace
function cannot be used simultaneously.
*5.When is set to Vcc1 > 2, the voltage of Vcc2 on the user system should be
3.3V or more. If using a CPU clock of 30MHz or more when the voltage of VCC1 is
higher than that of VCC2, set the SFR area of the intelligent I/O function to
2-wait (set the PM13 bit to "1") when reading this area. This precaution only
needs to be observed when using an emulator, and does not apply for the actual
MCU.
Spezifikationen CPE für R8C/Tiny
|
MCU supported
|
R8C/Tiny Series
R8C/10, R8C/11, R8C/12, R8C/13 Groups
R8C/14, R8C/15, R8C/16, R8C/17 Groups
R8C/18, R8C/19, R8C/1A, R8C/1B Groups
R8C/20, R8C/21, R8C/22, R8C/23 Groups
R8C/24, R8C/25 Groups
R8C/26, R8C/27 Groups
R8C/28, R8C/29 Groups
|
|
Maximum operating clock frequency
|
20MHz (at 3.0 to 5.0V)
10MHz (at 2.7 to 5.0V)
5MHz(at 2.2 to 5.0V)
|
|
MCU mode supported
|
Single-chip mode
|
|
Target system voltage
|
2.2 to 5.5V
|
|
Basic debugging function
|
Download, S/W break (64 points), Program execution/stop (allows free-run
execution and execution supporting S/W breaks) , Memory reference/setting
(reference/setting C-variables, run-time execution) , Register
reference/setting, Disassemble display, C-level debugging, etc.
|
|
Real-time tracing
|
Trace range
|
64K cycles
|
|
Trace data
|
20-bit address, 16-bit data, 12-bit MCU status
|
|
Trace modes
|
5 modes (Break/Before/About/After/Full)
|
|
Real-time RAM monitor
|
Range
|
1024 bytes (256 bytes x 4 blocks)
|
|
Results
|
Data, Latest access attribute (Read/Write/Non-accessed)
|
|
Hardware break function
|
2 points (Address break, R/W break, 255 pass counts) *1
|
|
Execution time measurement
|
Time between program start to stop is measurable.
|
|
PC Interface
|
USB (USB 1.1, Full-speed)
* Connectable to PC with a USB 2.0 port.
|
|
Power source for the emulator
(Available separately)
|
5.0V±5% DC/2A supplied from external source. (A power source unit is not
included.)
|
|
Power voltage
and power supply
|
User system connected
|
2.2 to 5.0V (Supplied from Vcc terminal on the user system.)
|
|
User system not connected
|
3.3V(Supplied from the emulator body)
|
|
Operating environmental conditions
|
[Temperature] 5 to 35ºC, [Humidity] 20 to 80%, [Dust and dirt] General office
environment
|
|
Storage environmental conditions
|
[Temperature] -10 to 60ºC, [Humidity] 0 to 90%, [Dust and dirt] General
office environment
|
|
Overseas standards
|
EN55022: 1998 Class A, EN55024: 1998
|
*1.The hardware break function and trace point setting of the real-time trace
function cannot be used simultaneously.
Systemkonfiguration
|
